← All posts
Print & DocumentPrinter care

Laser Printer Maintenance Kits: What's Inside and When

The fuser, the rollers and a counter that needs resetting: what the 'replace maintenance kit' message is asking for.

At some point a busy laser printer puts up a message that has nothing to do with toner. Depending on the brand it says “replace maintenance kit,” “maintenance kit low,” “replace fuser” or “replace PF kit.” The printer usually keeps working, so the message gets pressed past, sometimes for months. Then the jams start.

The message means the printer has counted enough pages to wear out the parts that move the paper and fix the toner to it. Those parts are sold together as a maintenance kit.

What’s in a maintenance kit

The exact contents depend on the model, but most kits contain some combination of these.

The fuser

The biggest and most expensive part. A fuser is a pair of rollers, one heated, that melts the toner and presses it into the paper. When it wears, toner smears or rubs off, pages come out wrinkled, and paper starts jamming at the back of the printer.

Pickup, feed and separation rollers

Rubber rollers that pull one sheet at a time out of the tray. Over time the rubber hardens and turns shiny, and the printer starts missing sheets or grabbing two at once. Brother sells these as a “PF kit” (paper feed kit), and some models have one for each tray.

The transfer roller

The roller that pulls toner off the drum onto the paper. When it’s worn, pages come out light or patchy even with a new toner cartridge.

HP describes its LaserJet kits as typically containing the fuser assembly and the pickup, separation and transfer rollers, while noting that contents vary by model. Toner and drums are not in the kit; they’re separate supplies.

How to tell when one is due

The printer’s own counter is the most reliable sign. Manufacturers rate each kit for a number of pages, and the printer warns you as it gets close. The ratings vary a lot between models. HP gives one of its kits a life of around 225,000 pages; Brother’s paper feed kits on some models are rated at about 50,000 or 100,000 pages, measured at a light standard coverage. Your own pages may wear the parts faster or slower.

Even before the message, the printer will tell you:

  • Jams that keep happening after you’ve cleared them and cleaned the rollers.
  • Two sheets feeding at once, or the printer saying a full tray is empty.
  • Toner that smudges or rubs off when you run a thumb across the page.
  • Wrinkled or curled pages coming out of the back.
  • A faint repeat of the image further down the page.

To check where you stand, print a configuration or supplies status page from the printer’s menu. It usually shows the page count and the remaining life of each part.

The printer usually keeps working, so the message gets pressed past, sometimes for months.

Who should fit it

Some kits are designed for an experienced person to fit with the instructions in the box. Others aren’t. Brother says the fuser and paper feed kit on some of its models cannot be installed by the customer and have to be replaced by Brother or an authorized service center. Check your model’s documentation before you buy anything.

If you’re doing it yourself, a few things matter:

  • Let the printer cool. The fuser runs hot enough to burn. Switch off, unplug and wait.
  • Get the right voltage. Many kits come in 110-volt and 220-volt versions. In the US you need the 110-volt kit, which HP describes as the one for 110 to 120-volt systems such as North America. The wrong one can damage the printer.
  • Match the part number to your exact model. Kits that look alike often aren’t interchangeable, and an incompatible kit can damage the printer and void its warranty, as HP warns.
  • Reset the counter afterward. The printer doesn’t know you’ve changed the parts. HP says to reset the maintenance counter after installing a kit, or the warning will keep coming back. The menu path varies by model and is in the user guide.
  • Print a test page. Then check that the pages are clean and the warning has cleared.

What it costs, and who pays

A maintenance kit costs more than a toner cartridge, but it lasts many times longer, so the cost per page is small. Our post on laser printer maintenance costs shows how to work that out.

Warranty coverage varies. Brother says periodic maintenance replacement is not covered under its standard warranty. HP says its kits carry their own warranty terms, which vary by kit and don’t cover normal wear. Read the terms for your model before assuming the manufacturer will pay.

Replacing single parts instead

Sometimes only one part is worn: a pickup roller in one tray, for example, on a printer that mostly pulls from another. Some manufacturers sell the rollers on their own, and replacing just the worn part can make sense. The catch is the counter. If you replace one part and reset the whole maintenance count, the printer will stop warning you about the parts you didn’t change.

The old parts

A used fuser is a mix of metal, rubber and electronics and doesn’t belong in the regular trash. Ricoh lists maintenance kits among the supplies its consumables recycling program takes back; for other brands, ask your supplier or use a certified electronics recycler. Our post on printer waste containers covers recycling options for the rest of a printer’s used supplies.

Done for you

If your printers and copiers are on a managed print agreement with us, maintenance supplies are included along with parts and labor. The devices report their page counts and parts life to us, so we see a kit coming due before the warning reaches your screen, and our technician fits it and resets the counter. For printers that aren’t on an agreement yet, our laser printer maintenance checklist covers the parts your team can look after in between.

More on Print & Document

Let's build your foundation.

Tell us where your business is today and we'll help map the next step.